1.pull yiur cartridges out of the p

1.pull yiur cartridges out of the printer and face them as shown note:you can reset jiust one cartridge,or both at the same time with this procedure
2.place a piece of tape so that it just covers the top 4 contacts on the top left side of the contact area as show
3.reinsert the cartridges into the printer with the tape in place
4.close the lid and wait about 5 seconds
5.open the lid and wait for the peinter to give the cartridges back to you note: the printer may take time to do this,and may flash toshow there is an error with your cartridges this normal
6.remove the cartridges again and move the tape to the other side as shown in the lower pictures
7.Reinsert the cartridges into the printer with the tape in place
8.Close the lid and wait about 5econds
9.open the lid ang wait for the printer to give the cartridges back to you.noet:the printer may flash to show there is an error with your cartridges again.this is nomal
10.remove the cartridges and remove all the tape.be sure the contacts are clean
11.place the cartridges back inothe priter.they sould now read 100% full if not.redo the procedure.but only cover the top 3 contacts.if they still do not show as full,repeat,but only cover the top 2 contacts
three cartridge method
on some models the above procedure won't work,and you'll have to fool the printer by keepng three cartridges on hand
(these cartridges can be old,empty cartridges).this works because the printer only remembers the last WTO cartridges.which were in it the procedure is as follows
?cart #1(empty)is removed for refilling
?cart #2 is installed
?cart #2 is removed
?cart #3 is installed
?cart #3 is removed
?cart #1(refilld)is installed the printer now thinks the filled cart is new

結果 (繁體中文) 1:

墨盒yiur 1pull的打印機，如圖所示，面對他們的注意：用一塊膠布，你可以在同一時間重置jiust一個墨盒，或兩者兼而有之，這個過程
2place它只是涵蓋了前4個觸點左上側的接觸面積，展會
的3reinsert到打印機墨盒中的磁帶地方的蓋子，等待約5秒鐘

4關閉5打開蓋子，等待peinter退給你注意的墨盒的打印機可能需要的時間來做到這一點，你的墨盒有一個錯誤可能會閃爍toshow
6remove這是正常的，再次移動磁帶的墨盒到另一側，如圖中的圖片
7reinsert下部到打印機墨盒代替與磁帶的蓋子，並等待約8close

9 5econds李安等待打印機，打開蓋子給的墨盒younoet的打印機可能會閃爍，表明您的NOMAL有錯誤，
10remove againthis硒鼓墨盒和刪除所有tape.be的時間觸點清潔現在
11place inothe priterthey高度重視和讀回的墨盒100％全，如果procedurebut notredo只包括前3個觸點。如果他們仍然不完整，重複顯示，但只覆蓋三個墨盒的方法

2，在上述過程中在某些機型上的接觸不會正常工作，你必須欺騙的手keepng三個墨盒的打印機
（可以是舊墨盒，空硒鼓）。這工作，因為打印機只記得最後的狗，程序是如下WTO cartridgeswhich的
？車#1（P）被刪除加氣站
？車#
2的安裝？車#
2被刪除？車#
3的安裝？車#
3被刪除？車#1（refilld）是安裝在打印機中車充滿認為，新的